EMBARKING ON-STARTING-BEGINNING YOUR DIY-DO-IT-YOURSELF-SELF-INSTALLED SHOWER DRAIN-BATHROOM DRAIN-DRAINAGE SYSTEM INSTALLATION-SETUP-PROJECT

Embarking On-Starting-Beginning Your DIY-Do-It-Yourself-Self-Installed Shower Drain-Bathroom Drain-Drainage System Installation-Setup-Project

Embarking On-Starting-Beginning Your DIY-Do-It-Yourself-Self-Installed Shower Drain-Bathroom Drain-Drainage System Installation-Setup-Project

Blog Article

Visit Link

They are making a few great pointers regarding How to Install a Shower Drain overall in this great article in the next paragraphs.


How to Install or Replace a Shower Drain
Upgrading a bathroom is among the extra preferred house renovation projects. Managing the plumbing for draining your shower can be exceptionally simple unless you overdo it.

Managing Your Own Shower Drainpipe Installation Job



Whether you are a bath tub or shower person, the majority of people seek shower just alternatives when getting a residence. This simple truth indicates greater than a few property owners invest a weekend break updating or installing showers in their restrooms. Thankfully for you, it is a relatively basic procedure.

A collector or pan describes the straight surface area situated at the end of the shower. The collector typically consists of a non-slip surface slightly banked towards the center or wherever the drain is located. Integrated with 3 to four inch walls around the side, the objective of your shower drainage plumbing is to obtain the water to flow to and down the drain.

You can literally develop a collection agency for your new shower, however you truly require to consider it. Do you truly wish to enter the issues of getting the sloping appropriate, as well as making certain every facet of it is water-proof? As well as I suggest every facet! It is a lot easier to merely get a pre-cast collection agency online or at your regional Lowes, House Depot or hardware store. Building one could seem like a wonderful suggestion, yet you will most likely feel differently after a couple of hrs.

No matter exactly how you tackle getting a frying pan, you must make every effort to use one that has the drain situated in the exact same area as the initial frying pan. Relocating the drainpipe pipes can be a task, specifically if the home builder used an unique framework structure. If you are determined to relocate the drain, you are going to need to cut back the pipeline or extend it, which might mean destroying large portions of the floor. Put another way, you are mosting likely to be taking a look at a multiple weekend break job.

Thinking we have our drainpipe lined up, the real attach is relatively easy. The water drainage pipe need to be dealing with vertical as much as the collector. It will certainly frequently resemble a "U", which implies it works as a cleanout to keep unpleasant scents from coming back up from the drainpipe. To connect the drainpipe, you are going to produce a water tight link in between a drain cap on the top of the frying pan and the water drainage pipe. Solutions differ, however you are commonly going to do this by placing a coupling item on the top of the water drainage pipe. This is after that covered with gaskets and actually screwed right into the drain cap. The drain cap need to serve as a locknut, to wit, it screws straight onto the combining.

The challenging part of this procedure is obtaining your drain cap to suit a water tight position in the pan. This is completed by backing off the drain cap when you make certain everything fits together. At that point, you placed plumbers putty around the underside of the cap and afterwards screw it back on. The putty needs to form a tight seal in between the cap and also the shower frying pan, which keeps water from trickling under it as well as right into the mounting under the shower.

Obviously, restroom showers been available in a variety of designs these days. If you purchase a collector, they usually included plumbing directions or the shop can keep in mind anything uncommon you should know. It sounds complex, however is usually quite easy. Enjoy!

How to Install or Replace a Shower Drain


The type of shower drain you install depends on several factors, including the flooring material and your particular scenario. Below are two popular options when it comes to installing a shower drain.


How to Install a Shower Drain on a Prefabricated Shower Pan


When renovating a bathroom, a new shower drain should always be part of the process. A drain assembly — which consists of a drain body, strainer, compression gasket, compression nut, compression wrench, drain nut, fiber gasket and rubber gasket — will cost you between $7 and $60 at your nearest hardware store. This is the piece you will attach to a preformed shower pan, a one-piece base that is usually made from acrylic and reinforced with fiberglass.



You’ll need some plumber’s putty to act as a sealant between the shower pan and the drain assembly. Roll the putty into a half-inch bead and wrap it around the underside of the drain body flange. Insert the drain body through the hole of the shower pan from the top and press down firmly (do not twist) to form an even seal.



At the bottom of the shower pan, place the rubber gasket and fiber gasket (in that order) onto the drain body. Insert the drain nut and tighten it with your hand. When it gets too hard to turn, use a set of adjustable pliers or a wrench to tighten it all the way through. Use your index finger to remove any excess putty from the top of the drain.



For this part, get a buddy to help you lower the shower pan onto the shower base. The shower base, in this scenario, is the substructure of the shower’s subfloor. It will have a drain hole with a 2-inch drain pipe located in the middle. The drainpipe should be positioned in the center of the drain body as you’re lowering the shower pan onto the shower base.



Once this is done, grab the compression gasket and insert it from the top of the hole, bevel side up, making sure that it fits in the space between the drain body and pipe. Push it down until it sets at the bottom.



Next, thread the compression nut over the drain pipe. Insert the compression wrench into the compression nut and tighten with a screwdriver. Finish the shower drain install by snapping strainer or drain cover onto the drain body.


How to Install a Shower Drain for a Tile Floor


Since tiles are square (in most cases), you will need a drain assembly with a square strainer. There are essentially three parts to a tile floor assembly: the drain barrel (where the strainer is attached), drain body and clamping ring.



Begin installing the shower drain after you’ve finished installing the subfloor and drain pipe. Fit the drain body over the drainpipe, ensuring that the flange is resting on the subfloor. Use solvent cement to bond them together.



Next comes the bottom mortar bed. Be sure to cover the drain body with a clean rag before you apply it so the drainpipe remains clean. Lay down the layer of mortar starting from the wall. Make sure there is a slope every ¼ inch per foot, all the way to the drain’s opening. The mortar bed should be flush with the drain body’s flange.



Wait for the mortar bed to dry. Afterward, install a pan liner on top of it. This is a waterproof membrane that catches any water that seeps through the mortar bed and directs it towards the drain. Cut a hole in the membrane around the drain hole and around the inner and outer mounting holes of the drain body. Screw some bolts into the outer mounting holes to secure the pan liner and drain body to the subfloor.



Place the clamping ring above the membrane. Align its mounting holes with the ones on the drain body and screw it in. This will sandwich the membrane between the drain body and the clamping ring. Fill the shower floor with 2 to 3 inches of water to check if the membrane has any leaks.



If there are no leaks, screw the drain barrel into the clamping ring; stop when it reaches the height you want. Leave at least 1 inch of space between the drain body and the top of the drain barrel. Apply another mortar bed layer on top of the pan membrane and finish installing the tile floor once it’s dry.


How to Replace a Shower Drain from Underneath


If the shower drain replacement is on a prefabricated shower pan, you have to go at it from the bottom. This will allow you to effectively take the drain assembly apart. Be sure to turn off the electricity in the area you’ll be working in before you begin. Then, use a flat screwdriver to pop the strainer out of the drain body to expose the compression nut. Insert your compression wrench into the compression nut and turn it counterclockwise with a screwdriver to unscrew it.



Using a combination of a utility knife and drywall saw, cut a rectangular hole in the ceiling beneath the drain. Make sure the hole is big enough to fit adjustable pliers and is along the joist so you have something to support the new drywall when patching it up. Use the adjustable pliers to loosen the drain until you can remove the rest of it with your hand. Follow that up by removing the rubber and fiber gaskets as well.



If you see that the drainpipe is welded or glued to a U-shaped pipe (also called the P-trap), you'll need to cut it. This will make it easier to push out the drain pipe and cut out the drain body. However, you'll need to know how to replace a shower drain trap as well once you cut it. Without the P-trap, sewer gases can travel into your home through the drain line. In addition to the unpleasant smell, long-term exposure to this gas can be harmful.



Install a new drainpipe in the shower base and repeat the steps on how to install a shower drain on a prefabricated shower pan. Repeat the above steps for installation — from inserting the drain body, to tightening the drain nut, to snapping the drain cover on top of the drain. However, since the shower pan is already on the floor, you don’t have to struggle with lowering and positioning it.



Assemble a new P-trap by gluing its pieces together and gluing the assembly to the drainpipe. Turn on the water and dash back downstairs to see if there are any leaks. If there are no leaks, patch up the drywall.


How to Replace a Shower Drain from the Top


When performing a shower drain replacement on tile flooring, you don’t need to go underneath. Start by unscrewing the drain barrel, cleaning the drainpipe and covering the hole to prevent debris from falling in it. Then, carefully pry out the tiles around the shower drain and chisel that area until the subfloor and mounting bolts are exposed. Unscrew the bolts and remove the clamping ring and drain body.



Install the new tile floor assembly while patching up the membrane and mortar bed. Don’t forget to check for leaks when you’re done. To patch the membrane, cut a new piece of membrane to fit the area you destroyed. Make holes for the drain and the mounting holes of the drain body. Apply caulk along the chiseled area and apply the patch. Leave the caulk to dry and patch the mortar bed with deck mud.

https://www.homeserve.com/en-us/blog/how-to/shower-drain-installation/


How to Choose the Best Drain for Your Shower

I'm very excited about Easy Shower Drain Installation Tips and I really hope you appreciated the entire blog entry. Appreciated our article? Please share it. Let somebody else locate it. I am grateful for your time. Visit again soon.

Report this page